Gearench U115H-000S PETOL HYDRA-TORK Bedienungsanleitung

Petol Hydra-Tork U115H-000S (Skid Mounted Base) Operating Manual Gearench P.O. Box 192 4450 South Highway 6 Clifton, Texas 766

8Periodic Inspection List for Petol Special Chain 1. PRIOR TO EACH USE, LEAF CHAIN AND TOOLS SHOULD BE INSPECTED FOR SERVICEABILITY AND LUB

9

10Safety Precautions 1. Always wear safety goggles to protect eyes. 2. Select the right tool for the job. 3. Keep tools in good condition.

11Installation Location The Petol Hydra-Tork Unit should be located in an area with adequate room to work the downhole tools. The unit may be locat

12Operation Controls The operating controls are shown on Figures 1 and 2 on page 16. The disconnect switch is used to disconnect electrical power t

13The hydraulic pressure gauge is used to indicate the current system pressure in psi. A conversion chart for equating the hydraulic pressure in ps

14

Loading To load the downhole tool in the unit, slide the vise left or right as needed. Adjust the vee-saddle to support the tool when set into the vi

16Breaking Out Load the tool and adjust the tong and vise as described above. Fully ratchet the tong. Turn the pressure control knob fully counter

17Parts List The following drawings, diagrams, and parts lists describe all parts, which may be needed as replacement items. Where appropriate, sta

iiTable of Contents Petol U115H-000S Hydra-Tork Description ... 1Warranty ...

Final Assembly Parts List Item Qty. Part Number Description Notes 1 1 UHBASE-115H-02 Base assembly 2 1 UHCN-115H-000 Console assembly See

Console Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCH-115-000 Hydraulic schematic 2 1 UHCN-P1-00 Control

20

21 Hydraulic Schematic Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCH-P02 Pump Oilgear PVW-06-LSAY-NNNN-729B 2 1

Control Panel Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCE-S1 Push button switch Allen-Bradley 800MB-CQA24GA 2 1

23

24Main Electrical Panel Parts List Item Qty. Part Number Description Make / Model Notes 1A 1 UHCE-S7 Disconnect switch Allen-Bradley 194R-NJ0

Cylinder Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCY-115H-0 Cylinder Vickers/Aeroquip TG10E4GB1FA12000

Vee Saddle Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHVSB-115H Vee saddle base 2 1 UHVSH-115H Vee saddl

Vise Assembly Parts List Item Qty. Part Number Description 1 1 TVB115H Base 2 1 TVJ115H Jaw 3 4 HI04D Diamond point insert 4 4 HP903 Insert key

1Petol U115H-000S Hydra-Tork Description The U115H-000S Petol Hydra-Tork unit was designed for making up and breaking out downhole tools. It is ra

Tong Assembly Parts List Item Qty. Part Number Description 1 1 VTDH115H Handle 2 1 HP356 Handle pin 3 1 TVJ115H Jaw 4A 2 HI04D Diamond point

29Petol Special Chain Parts List Item Qty. Part Number Description 1 As req’d 151-45-02 Special chain only 2 As req’d 151-45-05 Special chai

Electrical Schematic 30

2Warranty What Is Covered Gearench tools are expressly warranted to you, the purchaser, to be free of defects in material and workmanship. How Lon

3Forum Selection Clause Any dispute arising out of the sale and/or use of the GEARENCH tool that is the subject of this limited warranty shall be pr

4Safe Practices and Procedures Responsibility "It is the responsibility of the employer to train the employee in the proper selection and usage

5Safety Goggles must always be worn by persons in any area where hand and powered tools are being used. Never apply excess leverage to a wrench or

6Responsibility of Distributors IT IS THE RESPONSIBILITY OF THE PURCHASERS OF GEARENCH PRODUCTS TO CONVEY THE INFORMATION IN THIS PUBLICATION AND AN

7Abrasives - Accelerated wearing and scoring of the articulating chain members (pins and plates) may occur, with a corresponding reduction in chain