Gearench U118 PETOL HYDRA-TORK Bedienungsanleitung

Petol Hydra-Tork U118 Operating Manual Gearench P.O. Box 192 4450 South Highway 6 Clifton, Texas 76634 Phone: (254) 675-865

8 Periodic Inspection List for Petol Special Chain 1. PRIOR TO EACH USE, LEAF CHAIN AND TOOLS SHOULD BE INSPECTED FOR SERVICEABILITY AND LUB

9

10 Safety Precautions 1. Always wear safety goggles to protect eyes. 2. Select the right tool for the job. 3. Keep tools in good condition.

11 Installation Location The Petol Hydra-Tork Unit should be located in an area with adequate room to work the downhole tools. The unit may be locat

12 Operation Controls The operating controls are shown on Figures 1 and 2 on page 16. The disconnect switch is used to disconnect electrical power t

13 TORQUE-PRESSURE CONVERSION TORQUE (ft-lbs) PRESSURE (psig) TORQUE (ft-lbs) PRESSURE (psig) 0 0 30,000 940 10,000 315 31,000 970 11,000 345 32,00

14

Loading To load the downhole tool in the unit, slide the vise left or right as needed. Adjust the vee-saddle to support the tool when set into the v

16 Breaking Out Load the tool and adjust the tong and vise as described above. Fully ratchet the tong. Turn the pressure control knob fully counter

17 Parts List The following drawings, diagrams, and parts lists describe all parts, which may be needed as replacement items. Where appropriate, sta

ii Table of Contents Petol U118 Hydra-Tork Description... 1 Warran

Final Assembly Parts List Item Qty. Part Number Description Notes 1 1 UHBASE-118-01 Base assembly 2 1 UHCN-118-000 Console assembly See pag

Console Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCH-118-000 Hydraulic schematic 2 1 UHCN-P!-00 Contro

Hydraulic Schematic 20

21 Hydraulic Schematic Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCH-P03 Pump Oilgear PVW-20-LSAY-NNNN-885B 2 1 UHC

Control Panel Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCE-S1 Push button switch Allen-Bradley 800MB-CQA24GA 2 2

Main Electrical Panel Parts List 23

24 Item Qty. Part Number Description Make / Model Notes 1A 1 UHCE-S7 Disconnect switch Allen-Bradley 194R-NJ030P34ER1 1B 3 UHCE-F1 Fuse, 230V

Cylinder Carriage Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCY-118-0 Cylinder Vickers/Aeroquip TG10HWLB1SA2400 2

Vee Saddle Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHVSB-118 Vee saddle base 2 1 UHVSH-118 Vee saddle

Vise Assembly Parts List Item Qty. Part Number Description 1 1 TVB118 Base 2 1 TVJ118 Jaw 3 4 HI10D Diamond point insert 4 4 HP904 Insert key 5

1 Petol U118 Hydra-Tork Description The U118 Petol Hydra-Tork unit was designed for making up and breaking out downhole tools. It is rated for oper

Tong Assembly Parts List Item Qty. Part Number Description 1 1 VTDH118 Handle 2 1 HP276 Handle pin 3 1 TVJ118 Jaw 4A 2 HI10D Diamond point i

29 Petol Special Chain Parts List Item Qty. Part Number Description 1 As req’d 181-45-02 Special chain only 2 As req’d 181-45-05 Special chai

Electrical Schematic 30

2 Warranty What Is Covered Gearench tools are expressly warranted to you, the purchaser, to be free of defects in material and workmanship. How Long

3 Forum Selection Clause Any dispute arising out of the sale and/or use of the GEARENCH tool that is the subject of this limited warranty shall be pr

4 Safe Practices and Procedures Responsibility "It is the responsibility of the employer to train the employee in the proper selection and usage

5 Safety Goggles must always be worn by persons in any area where hand and powered tools are being used. Never apply excess leverage to a wrench or

6 Responsibility of Distributors IT IS THE RESPONSIBILITY OF THE PURCHASERS OF GEARENCH PRODUCTS TO CONVEY THE INFORMATION IN THIS PUBLICATION AND AN

7 Abrasives - Accelerated wearing and scoring of the articulating chain members (pins and plates) may occur, with a corresponding reduction in chain